Copper rope - hard, bare BS (British Standard)

Copper rope – hard, bare

according to BS 7884:1997

BS 7884:1997

		nominalcross section	no. of wire	wirediameter	cond.diameter	calculated breaking force	calc. conductorresistance at 20°C
		mm²		mm	mm	kN	Ohm/km
100771	Cu Strand	10	7	1,35	4,05	3,75	1,8290
100751	Cu Strand	12	7	1,70	4,95	6,97	1,7802
100772	Cu Strand	14	7	1,60	4,80	5,27	1,3030
100753	Cu Strand	16	3	2,65	5,70	6,19	1,1060
100773	Cu Strand	16	7	1,70	5,10	8,88	1,3990
100780	Cu Strand	22	7	2,00	6,00	12,29	1,0110
100754	Cu Strand	25	7	2,10	6,30	13,55	0,9171
100781	Cu Strand	30	7	2,30	6,90	16,26	0,7645
100755	Cu Strand	32	3	3,75	8,06	12,70	0,5520
100756	Cu Strand	32	7	2,46	7,38	12,44	0,5497
100758	Cu Strand	35	7	2,50	7,50	19,21	0,6471
100759	Cu Strand	38	7	2,60	7,80	20,78	0,5983
100782	Cu Strand	45	7	2,90	8,70	24,60	0,4809
100760	Cu Strand	50	7	3,00	9,00	18,52	0,3706
100774	Cu Strand	50	19	1,80	9,00	17,70	0,3819
100783	Cu Strand	55	7	3,20	9,60	29,95	0,3950
100761	Cu Strand	70	7	3,55	10,65	25,96	0,2646
100762	Cu Strand	70	19	2,10	10,50	35,99	0,3402

→ Other cross-sections on request.

Technical values can change. No responsibility is therefore taken for correctness.

Copper rope – hard, bare

according to BS 7884:1997

		nominal cross section	no. of wire	wirediameter	cond.diameter	calculated breaking force	calc. conductorresistance at 20°C
		mm²		mm	mm	kN	Ohm/km
100752	Cu Strand	75	7	3,70	11,10	38,01	0,2954
100775	Cu Strand	95	19	2,50	12,50	51,01	0,2400
100763	Cu Strand	100	7	4,30	12,90	51,16	0,2195
100765	Cu Strand	120	19	2,80	14,00	60,89	0,1914
100766	Cu Strand	125	19	2,90	14,50	65,31	0,1784
100776	Cu Strand	150	19	3,20	16,00	79,53	0,1465
100767	Cu Strand	150	37	2,25	15,75	80,49	0,1533
100770	Cu Strand	180	19	3,50	17,50	95,14	0,1225
100769	Cu Strand	180	37	2,50	17,50	99,33	0,1242
100777	Cu Strand	185	19	3,55	17,75	68,86	0,0981
100778	Cu Strand	185	37	2,50	17,50	68,49	0,1024
100757	Cu Strand	200	19	3,70	18,50	100,90	0,1696
100779	Cu Strand	240	19	4,00	20,00	117,90	0,0938

→ Other cross-sections on request.

Technical values can change. No responsibility is therefore taken for correctness.